login
Search
xbacklight doesn't seem to work on my HP dv4-1435dx with an intel
GM45. xrandr shows no "Range" for the backlight. The screen brightness
does change, but it is affected by the presence of a power chord at
bootup.
The other problem is the monitor support. I can use an external
monitor fine by itself, but if I want to use both the VGA and LVDS i
can't set the display sizes independently, and i can't set them to be
separate screens, i.e. they both show the same desktop.
I am using a recent snapshot
$ xrandr --output VGA --auto --right-of LVDS
xrandr: screen cannot be larger than 1280x1280 (desired size 2304x1024)
with the VGA setup at 1280x1024 i try to set the laptop display.
I have no idea where the "desired size" is coming from
$ xrandr --output LVDS --mode 1024x768 --left-of VGA
xrandr: screen cannot be larger than 1280x1280 (desired size 2304x1024)
$ xrandr --verbose
Screen 0: minimum 320 x 200, current 1280 x 1024, maximum 1280 x 1280
VGA connected 1280x1024+0+0 (0x3e) normal (normal left inverted right
x axis y axis) 338mm x 270mm
Identifier: 0x3b
Timestamp: -329300275
Subpixel: unknown
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID_DATA:
00ffffffffffff005a631c3601010101
150f010308221b782adc55a359489e24
115054bfef808180714f010101010101
010101010101302a009851002a403070
1300520e1100001e000000ff00505533
3035323130303830360a000000fd0037
4d18520e000a202020202020000000fc
005137620a2020202020202020200094
1280x1024 (0x3e) 108.0MHz +HSync +VSync *current +preferred
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock
64.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock
60.0Hz
1280x1024 (0x3f) 135.0MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock
80.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock
75.0Hz
1280x1024 (0x3e) 108.0MHz +HSync +VSync *current
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock
64.0KHz
v: height 1024 start 1025 end 1028 total 1066 clock
60.0Hz
1152x864 (0x40) 108.0MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock
67.5KHz
v: height 864 start 865 end 868 total 900 clock
75.0Hz
1024x768 (0x41) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock
60.0KHz
v: height 768 start 769 end 772 total 800 clock
75.0Hz
1024x768 (0x42) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock
56.5KHz
v: height 768 start 771 end 777 total 806 clock
70.1Hz
1024x768 (0x43) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock
60.0Hz
832x624 (0x44) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock
49.7KHz
v: height 624 start 625 end 628 total 667 clock
74.6Hz
800x600 (0x45) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock
48.1KHz
v: height 600 start 637 end 643 total 666 clock
72.2Hz
800x600 (0x46) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock
46.9KHz
v: height 600 start 601 end 604 total 625 clock
75.0Hz
800x600 (0x47) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock
60.3Hz
800x600 (0x48) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock
35.2KHz
v: height 600 start 601 end 603 total 625 clock
56.2Hz
640x480 (0x49) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock
37.5KHz
v: height 480 start 481 end 484 total 500 clock
75.0Hz
640x480 (0x4a) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock
37.9KHz
v: height 480 start 489 end 492 total 520 clock
72.8Hz
640x480 (0x4b) 30.2MHz -HSync -VSync
h: width 640 start 704 end 768 total 864 skew 0 clock
35.0KHz
v: height 480 start 483 end 486 total 525 clock
66.7Hz
640x480 (0x4c) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock
59.9Hz
720x400 (0x4d) 28.3MHz -HSync +VSync
h: width 720 start 738 end 846 total 900 skew 0 clock
31.5KHz
v: height 400 start 412 end 414 total 449 clock
70.1Hz
LVDS connected (normal left inverted right x axis y axis)
Identifier: 0x3c
Timestamp: -329300275
Subpixel: horizontal rgb
Clones:
CRTCs: 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID_DATA:
00ffffffffffff004ca3424d00000000
00120103801e13780a87f594574f8c27
27505400000001010101010101010101
010101010101141b0088502010300c40
33002fbe100000190000000f00000000
00000000002387026400000000fe0053
414d53554e470a2020202020000000fe
00313431415430332d3330310a2000a3
PANEL_FITTING: full_aspect
supported: center full_aspect full
BACKLIGHT_CONTROL: combination
supported: native legacy combination kernel
BACKLIGHT: 0 (0x00000000) range: (0,0)
1280x800 (0x4e) 69.3MHz -HSync -VSync +preferred
h: width 1280 start 1292 end 1356 total 1416 skew 0 clock
49.0KHz
v: height 800 start 803 end 806 total 816 clock
60.0Hz
1024x768 (0x4f) 94.5MHz +HSync +VSync
h: width 1024 start 1072 end 1168 total 1376 skew 0 clock
68.7KHz
v: height 768 start 769 end 772 total 808 clock
85.0Hz
1024x768 (0x41) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock
60.0KHz
v: height 768 start 769 end 772 total 800 clock
75.0Hz
1024x768 (0x42) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock
56.5KHz
v: height 768 start 771 end 777 total 806 clock
70.1Hz
1024x768 (0x43) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock
48.4KHz
v: height 768 start 771 end 777 total 806 clock
60.0Hz
832x624 (0x44) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock
49.7KHz
v: height 624 start 625 end 628 total 667 clock
74.6Hz
800x600 (0x50) 56.3MHz +HSync +VSync
h: width 800 start 832 end 896 total 1048 skew 0 clock
53.7KHz
v: height 600 start 601 end 604 total 631 clock
85.1Hz
800x600 (0x45) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock
48.1KHz
v: height 600 start 637 end 643 total 666 clock
72.2Hz
800x600 (0x46) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock
46.9KHz
v: height 600 start 601 end 604 total 625 clock
75.0Hz
800x600 (0x47) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock
37.9KHz
v: height 600 start 601 end 605 total 628 clock
60.3Hz
800x600 (0x48) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock
35.2KHz
v: height 600 start 601 end 603 total 625 clock
56.2Hz
640x480 (0x51) 36.0MHz -HSync -VSync
h: width 640 start 696 end 752 total 832 skew 0 clock
43.3KHz
v: height 480 start 481 end 484 total 509 clock
85.0Hz
640x480 (0x4a) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock
37.9KHz
v: height 480 start 489 end 492 total 520 clock
72.8Hz
640x480 (0x49) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock
37.5KHz
v: height 480 start 481 end 484 total 500 clock
75.0Hz
640x480 (0x4c) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock
31.5KHz
v: height 480 start 490 end 492 total 525 clock
59.9Hz
720x400 (0x52) 35.5MHz -HSync +VSync
h: width 720 start 756 end 828 total 936 skew 0 clock
37.9KHz
v: height 400 start 401 end 404 total 446 clock
85.0Hz
640x400 (0x53) 31.5MHz -HSync +VSync
h: width 640 start 672 end 736 total 832 skew 0 clock
37.9KHz
v: height 400 start 401 end 404 total 445 clock
85.1Hz
640x350 (0x54) 31.5MHz +HSync -VSync
h: width 640 start 672 end 736 total 832 skew 0 clock
37.9KHz
v: height 350 start 382 end 385 total 445 clock
85.1Hz
HDMI-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x3d
Timestamp: -329300275
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BROADCAST_RGB: 0 (0x00000000) range: (0,1)
$ cat Xorg.0.log
(--) checkDevMem: using aperture driver /dev/xf86
(--) Using wscons driver on /dev/ttyC4 in pcvt compatibility mode (version
3.32)
X.Org X Server 1.6.5
Release Date: 2009-10-11
X Protocol Version 11, Revision 0
Build Operating System: OpenBSD 4.7 amd64
Current Operating System: OpenBSD ghost.funny.org 4.7 GENERIC.MP#179 amd64
Build Date: 07 April 2010 05:57:28PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Apr 11 05:11:19 2010
(II) Loader magic: 0x1b40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on openbsd
(--) PCI:*(0:0:2:0) 8086:2a42:103c:30f7 Intel GM45 Video rev 7, Mem @
0xd0000000/4194304, 0xc0000000/268435456, I/O @ 0x000060f0/8
(--) PCI: (0:0:2:1) 8086:2a43:103c:30f7 Intel GM45 Video rev 7, Mem @
0xd5400000/1048576
(==) Using default built-in configuration (21 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default intel Device 0"
Driver "intel"
EndSection
Section "Screen"
Identifier "Builtin Default intel Screen 0"
Device "Builtin Default intel Device 0"
EndSection
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default intel Screen 0"
Screen "Builtin Default vesa Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(==) Not automatically adding devices
(==) Not automatically enabling devices
(==) FontPath set to:
/usr/X11R6/lib/X11/fonts/misc/,
/usr/X11R6/lib/X11/fonts/TTF/,
/usr/X11R6/lib/X11/fonts/OTF,
/usr/X11R6/lib/X11/fonts/Type1/,
/usr/X11R6/lib/X11/fonts/100dpi/,
/usr/X11R6/lib/X11/fonts/75dpi/
(==) ModulePath set to "/usr/X11R6/lib/modules"
(==) |-->Input Device "<default pointer>"
(==) |-->Input Device "<default keyboard>"
(==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
(==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
(II) System resource ranges:
[0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[3] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[4] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/X11R6/lib/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/X11R6/lib/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 2.7.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "vesa"
(II) Loading /usr/X11R6/lib/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 2.2.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.4.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
Mobile IntelB. GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[3] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[4] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(WW) Falling back to old probe method for vesa
(II) resource ranges after probing:
[0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[3] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[4] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[5] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[6] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[7] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[8] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[9] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) intel(0): Creating default Display subsection in Screen section
"Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) Mobile IntelB.
GM45 Express Chipset
(--) intel(0): Chipset: "Mobile IntelB. GM45 Express Chipset"
(--) intel(0): Linear framebuffer at 0xC0000000
(--) intel(0): IO registers at addr 0xD0000000
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(==) intel(0): Using EXA for acceleration
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): Attempting to determine panel fixed mode.
(II) intel(0): I2C device "LVDSDDC_C:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B"
registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): Output HDMI-1 has no monitor section
(II) intel(0): I2C bus "HDMIDDC_B" initialized.
(II) intel(0): HDMI output 1 detected
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C"
registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(==) intel(0): Write-combining range (0xa0000,0x10000) was already clear
(II) intel(0): Resizable framebuffer: not available (1 3)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using EDID range info for horizontal sync
(II) intel(0): Using EDID range info for vertical refresh
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Output VGA connected
(II) intel(0): Output LVDS connected
(II) intel(0): Output HDMI-1 disconnected
(II) intel(0): Using fuzzy aspect match for initial modes
(II) intel(0): Output VGA using initial mode 1024x768
(II) intel(0): Output LVDS using initial mode 1024x768
(==) intel(0): Write-combining range (0xa0000,0x10000) was already clear
(II) intel(0): detected 512 kB GTT.
(II) intel(0): detected 65532 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(**) intel(0): Display dimensions: (340, 270) mm
(**) intel(0): DPI set to (95, 120)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/X11R6/lib/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.6.5, module version = 2.4.0
ABI class: X.Org Video Driver, version 5.0
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to
0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(WW) intel(0): Register 0x61110 (PORT_HOTPLUG_EN) changed from
0x00000120 to 0x38000120
(WW) intel(0): Register 0x61114 (PORT_HOTPLUG_STAT) changed from
0x00000b00 to 0x18580b00
(WW) intel(0): Register 0x321b (FBC_FENCE_OFF) changed from 0x73010600
to 0x74015500
(II) UnloadModule: "vesa"
(II) Unloading /usr/X11R6/lib/modules/drivers//vesa_drv.so
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[1] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[2] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[3] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[4] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[5] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[6] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[7] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[8] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[9] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 1006592 total, 0 used
(II) intel(0): I830CheckAvailableMemory: 4026368 kB available
(WW) intel(0): DRI2 requires UXA
drmOpenDevice: node name is /dev/drm0
drmOpenDevice: open result is 11, (OK)
drmOpenDevice: node name is /dev/drm0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/drm0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) [drm] DRM interface version 1.2
(II) [drm] DRM open master succeeded.
(II) intel(0): [drm] Using the DRM lock SAREA also for drawables.
(II) intel(0): [drm] framebuffer mapped by ddx driver
(II) intel(0): [drm] added 1 reserved context for kernel
(II) intel(0): X context handle = 0x1
(II) intel(0): [drm] installed DRM signal handler
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) intel(0): [drm] Registers = 0x40002000
(II) intel(0): [drm] ring buffer = 0x40082000
(II) intel(0): [drm] mapped front buffer at 0xc088e000, handle = 0x400a2000
(II) intel(0): [drm] mapped back buffer at 0xc218f000, handle = 0x406e2000
(II) intel(0): [drm] mapped depth buffer at 0xc27cf000, handle = 0x40d22000
(II) intel(0): [drm] mapped classic textures at 0xc4000000, handle =
0x41362000
(II) intel(0): [drm] Initialized kernel agp heap manager, 33554432
(II) intel(0): [dri] visual configs initialized
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is
0x0000
(==) intel(0): Write-combining range (0xa0000,0x10000) was already clear
(II) EXA(0): Offscreen pixmap area of 19660800 bytes
(II) EXA(0): Driver registered support for the following operations:
(II) Solid
(II) Copy
(II) Composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): [DRI] installation complete
(II) intel(0): Disable render standby.
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x03fff000 (pgoffset 16383)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x04000000 (pgoffset 16384)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x0001ffff: ring buffer (128 kB)
(II) intel(0): 0x00020000-0x00083fff: compressed frame buffer (400 kB,
0x00000000bc020000 physical
)
(II) intel(0): 0x00084000-0x0008dfff: HW cursors (40 kB)
(II) intel(0): 0x0008e000-0x0088dfff: fake bufmgr (8192 kB)
(II) intel(0): 0x0088e000-0x00ecdfff: front buffer (6400 kB) X tiled
(II) intel(0): 0x00ece000-0x0218dfff: exa offscreen (19200 kB)
(II) intel(0): 0x0218e000-0x0218efff: power context (4 kB)
(II) intel(0): 0x0218f000-0x027cefff: back buffer (6400 kB) X tiled
(II) intel(0): 0x027cf000-0x02e0efff: depth buffer (6400 kB) Y tiled
(II) intel(0): 0x03fff000: end of stolen memory
(II) intel(0): 0x03fff000-0x03ffffff: HW status (4 kB)
(II) intel(0): 0x04000000-0x05ffffff: classic textures (32768 kB)
(II) intel(0): 0x10000000: end of aperture
(WW) intel(0): ESR is 0x00000010, page table error
(WW) intel(0): PGTBL_ER is 0x00100000, CS instruction GTT PTE
(WW) intel(0): Existing errors found in hardware state.
(II) intel(0): using SSC reference clock of 100 MHz
(II) intel(0): Selecting standard 18 bit TMDS pixel format.
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is on
(II) intel(0): Display plane A is now enabled and connected to pipe A.
(II) intel(0): Pipe B is on
(II) intel(0): Display plane B is now enabled and connected to pipe B.
(II) intel(0): Output VGA is connected to pipe A
(II) intel(0): Output LVDS is connected to pipe B
(II) intel(0): Output HDMI-1 is connected to pipe none
(II) intel(0): [drm] dma control initialized, using IRQ 11
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled
message.
(II) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): direct rendering: XF86DRI Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/drm0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/drm0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/X11R6/lib/modules/dri/i965_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) intel(0): Setting screen physical size to 303 x 190
(WW) <default pointer>: No Device specified, looking for one...
(II) <default pointer>: found Device "/dev/wsmouse"
(**) <default pointer>: Protocol: WSMouse
(**) Option "CorePointer"
(**) <default pointer>: always reports core events
(**) Option "Device" "/dev/wsmouse"
(==) <default pointer>: Emulate3Buttons, Emulate3Timeout: 50
(**) <default pointer>: ZAxisMapping: buttons 4 and 5
(**) <default pointer>: Buttons: 9
(II) XINPUT: Adding extended input device "<default pointer>" (type: MOUSE)
(**) <default pointer>: (accel) keeping acceleration scheme 1
(**) <default pointer>: (accel) filter chain progression: 2.00
(**) <default pointer>: (accel) filter stage 0: 20.00 ms
(**) <default pointer>: (accel) set acceleration profile 0
(**) Option "CoreKeyboard"
(**) <default keyboard>: always reports core events
(**) Option "Protocol" "standard"
(**) <default keyboard>: Protocol: standard
(--) <default keyboard>: using wscons layout us
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) <default keyboard>: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) <default keyboard>: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) <default keyboard>: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) <default keyboard>: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "<default keyboard>" (type:
KEYBOARD)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): [drm] mapped front buffer at 0xc088e000, handle = 0x43362000
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) 3rd Button detected: disabling emulate3Button
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0 69.32 1280 1292 1356 1416
800 803 806 816 -hsync -vsync (49.0 kHz)
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register"
registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): Using hsync ranges from config file
(II) intel(0): Using vrefresh ranges from config file
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600
601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600
601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480
481 484 500 -hsync -vsync (37.5 kHz)
(II) intel(0): Modeline "640x480"x0.0 31.50 640 664 704 832 480
489 492 520 -hsync -vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480
483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480
490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400
412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688
1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312
768 769 772 800 +hsync +vsync (60.0 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328
768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344
768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624
625 628 667 -hsync -vsync (49.7 kHz)
(II) intel(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600
601 604 625 +hsync +vsync (46.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 50.00 800 856 976 1040 600
637 643 666 +hsync +vsync (48.1 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688
1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600
864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): EDID vendor "VSC", prod id 13852
(II) intel(0): EDID vendor "SEC", prod id 19778
dmesg
OpenBSD 4.7-current (GENERIC.MP) #179: Wed Apr 7 21:07:50 MDT 2010
deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 3117854720 (2973MB)
avail mem = 3021164544 (2881MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xe8270 (29 entries)
bios0: vendor Hewlett-Packard version "F.42" date 05/14/2009
bios0: Hewlett-Packard HP Pavilion dv4 Notebook PC
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP DMAR SSDT HPET APIC MCFG ASF! SLIC BOOT SSDT
acpi0: wakeup devices SLPB(S4) P32_(S0) UHC1(S0) UHC2(S0) UHC3(S0)
UHC6(S0) EHC1(S0) UHC4(S0) UHC5(S0) EHC2(S0) PXSX(S4) EXP1(S5)
PXSX(S4) EXP3(S5) PXSX(S4) EXP4(S5) LANR(S5) PXSX(S4) EXP5(S5)
PXSX(S4) EXP6(S5) MIR_(S5)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz, 2095.07 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX1
6,xTPR,PDCM,SSE4.1,XSAVE,NXE,LONG
cpu0: 2MB 64b/line 8-way L2 cache
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz, 2094.75 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX1
6,xTPR,PDCM,SSE4.1,XSAVE,NXE,LONG
cpu1: 2MB 64b/line 8-way L2 cache
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 4
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 8 (P32_)
acpiprt2 at acpi0: bus 1 (EXP1)
acpiprt3 at acpi0: bus 2 (EXP3)
acpiprt4 at acpi0: bus 3 (EXP4)
acpiprt5 at acpi0: bus 4 (EXP5)
acpiprt6 at acpi0: bus 5 (EXP6)
acpiec0 at acpi0
acpicpu0 at acpi0: C3, C2, C1, PSS
acpicpu1 at acpi0: C3, C2, C1, PSS
acpipwrres0 at acpi0: FN00
acpitz0 at acpi0: critical temperature 97 degC
acpibtn0 at acpi0: PWRB
acpibtn1 at acpi0: LID0
acpibtn2 at acpi0: SLPB
acpibat0 at acpi0: BAT0 model "Primary" type Lion oem "Hewlett-Packard"
acpiac0 at acpi0: AC unit offline
acpivideo0 at acpi0: OVGA
acpivideo1 at acpi0: EVGA
acpivout0 at acpivideo1: LCD_
acpivout1 at acpivideo1: CRT_
acpivout2 at acpivideo1: HDMI
cpu0: Enhanced SpeedStep 2094 MHz: speeds: 2100, 1600, 1200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel GM45 Host" rev 0x07
vga1 at pci0 dev 2 function 0 "Intel GM45 Video" rev 0x07
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xc0000000, size 0x10000000
inteldrm0 at vga1: apic 4 int 16 (irq 11)
drm0 at inteldrm0
"Intel GM45 Video" rev 0x07 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x03: apic 4
int 16 (irq 11)
uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x03: apic 4
int 17 (irq 10)
ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x03: apic 4
int 18 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x03:
apic 4 int 22 (irq 11)
azalia0: codecs: IDT 92HD71B7, AT&T/Lucent/0x1040, Intel/0x2802, using
IDT 92HD71B7
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x03: apic 4
int 16 (irq 255)
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 2 "Intel 82801I PCIE" rev 0x03: apic 4
int 18 (irq 255)
pci2 at ppb1 bus 2
"Broadcom BCM4315" rev 0x01 at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 28 function 3 "Intel 82801I PCIE" rev 0x03: apic 4
int 19 (irq 255)
pci3 at ppb2 bus 3
re0 at pci3 dev 0 function 0 "Realtek 8101E" rev 0x02: RTL8102EL
(0x2480), apic 4 int 19 (irq 11), address 00:23:5a:a6:6d:37
rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1
ppb3 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x03: apic 4
int 16 (irq 255)
pci4 at ppb3 bus 4
"JMicron SD/MMC" rev 0x00 at pci4 dev 0 function 0 not configured
sdhc0 at pci4 dev 0 function 2 "JMicron SD Host Controller" rev 0x00:
apic 4 int 16 (irq 11)
sdmmc0 at sdhc0
"JMicron Memory Stick" rev 0x00 at pci4 dev 0 function 3 not configured
"JMicron xD" rev 0x00 at pci4 dev 0 function 4 not configured
ppb4 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x03: apic 4
int 17 (irq 255)
pci5 at ppb4 bus 5
uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x03: apic 4
int 20 (irq 11)
uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x03: apic 4
int 22 (irq 11)
uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x03: apic 4
int 18 (irq 11)
ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x03: apic 4
int 20 (irq 11)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb5 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x93
pci6 at ppb5 bus 8
pcib0 at pci0 dev 31 function 0 "Intel 82801IBM LPC" rev 0x03
ahci0 at pci0 dev 31 function 2 "Intel 82801I AHCI" rev 0x03: apic 4
int 21 (irq 11), AHCI 1.2
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, Hitachi HTS54323, FB4O> SCSI3 0/direct
fixed
sd0: 305245MB, 512 bytes/sec, 625142448 sec total
cd0 at scsibus0 targ 1 lun 0: <TSSTcorp, CDDVDW TS-L633M, 0200> ATAPI
5/cdrom removable
ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x03: apic
4 int 18 (irq 11)
iic0 at ichiic0
lisa0 at iic0 addr 0x1d: lis331dl
spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
mtrr: Pentium Pro MTRR support
umass0 at uhub1 port 2 configuration 1 interface 0 "Flash Drive
SK_USB20" rev 2.00/2.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Flash, Drive SK_USB20, 1.00> SCSI2
0/direct removable
sd1: 7782MB, 512 bytes/sec, 15937536 sec total
run0 at uhub1 port 3 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 3
run0: MAC/BBP RT3070 (rev 0x0200), RF RT3020 (MIMO 1T1R), address
00:22:cf:04:06:64
uvideo0 at uhub1 port 5 configuration 1 interface 0 "Image Processor
HP Webcam" rev 2.00/3.04 addr 4
video0 at uvideo0
uhidev0 at uhub4 port 1 configuration 1 interface 0 "Primax
Electronics USB Optical Mouse" rev 2.00/2.00 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse1 at ums0 mux 0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
sd1 detached
scsibus1 detached
umass0 detached
uhidev1 at uhub4 port 2 configuration 1 interface 0 "Dell Dell USB
Keyboard" rev 1.10/3.50 addr 3
uhidev1: iclass 3/1
ukbd0 at uhidev1: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
--
Later
Peter
