Hi everyone,
I had trouble with my Asus Mainboard (P5BV-C/4L, Intel i3200 Chipset, ICH7+Marvell Controllers) with all the recent kernel versions (although I can't tell if the problem existet with older kernels since it's a system I set up just recently). I got a lot of timeout errors and bus-resets on both the ide and the sata ports (more precisely on the ICH7 sata, Marvell 88SE6145 sata, the promise Ultra100 TX2 ide and the JMicron 20360/20363 sata and ide ports). The problem occured less often when I didn't let the drives go to standby, but it nontheless persisted.
Following the recommomendations on http://ata.wiki.kernel.org/index.php/Libata_error_messages [1] I added the pci=nomsi kernelparameter. This solved the problem for me. At least I got no futher errors since two days. So far I haven't experienced any performance penalties - as far as I understand the MSI thing I should'nt right? Well at least it looks like Asus didn't do their homework BIOS-wise.
I appended my dmesg and lspci output. I'm hoping this post is of help for anyone expieriencing the same kind of troubles.
Best regards, Matthias P.
lspci:
00:00.0 Host bridge: Intel Corporation Server DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation Server Host-Primary PCI Express Bridge (rev 01) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01) 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01) 00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) 00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:00.0 Mass storage controller: Promise Technology, Inc. PDC20268 (Ultra100 TX2) (rev 02) 01:03.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics Innovation) Volari Z7 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 12) 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 12) 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 12) 05:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 12) 06:00.0 RAID bus controller: Marvell Technology Group Ltd. 88SE6145 SATA II PCI-E controller (rev a1) 07:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 03) 07:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 HCI Controller (rev 03)
dmesg:
Linux version 2.6.25-gentoo-r7 (root@xxx) (gcc version 4.1.2 (Gentoo
4.1.2 p1.1)) #1 SMP Thu Aug 7 10:10:58 CEST 2008
Command line: root=/dev/sda3 pci=nomsi
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000099800 (usable)
BIOS-e820: 0000000000099800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dffb0000 (usable)
BIOS-e820: 00000000dffb0000 - 00000000dffbe000 (ACPI data)
BIOS-e820: 00000000dffbe000 - 00000000dffd0000 (ACPI NVS)
BIOS-e820: 00000000dffd0000 - 00000000dffde000 (reserved)
BIOS-e820: 00000000dffe0000 - 00000000e0000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Entering add_active_range(0, 0, 153) 0 entries of 256 used
Entering add_active_range(0, 256, 917424) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1179648) 2 entries of 256 used
end_pfn_map = 1179648
DMI present.
ACPI: RSDP 000FA660, 0024 (r2 ACPIAM)
ACPI: XSDT DFFB0100, 0044 (r1 110607 XSDT1010 20071106 MSFT 97)
ACPI: FACP DFFB0290, 00F4 (r3 110607 FACP1010 20071106 MSFT 97)
ACPI: DSDT DFFB0440, 55F6 (r1 S0052 S0052000 0 INTL 20060113)
ACPI: FACS DFFBE000, 0040
ACPI: APIC DFFB0390, 006C (r1 110607 APIC1010 20071106 MSFT 97)
ACPI: MCFG DFFB0400, 003C (r1 110607 OEMMCFG 20071106 MSFT 97)
ACPI: OEMB DFFBE040, 0061 (r1 110607 OEMB1010 20071106 MSFT 97)
Entering add_active_range(0, 0, 153) 0 entries of 256 used
Entering add_active_range(0, 256, 917424) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1179648) 2 entries of 256 used
early res: 0 [0-fff] BIOS data page
early res: 1 [6000-7fff] SMP_TRAMPOLINE
early res: 2 [200000-7a01cf] TEXT DATA BSS
early res: 3 [99800-9f7ff] EBDA
early res: 4 [8000-dfff] PGTABLE
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
[ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
[ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
[ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
[ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
[ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
[ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
[ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
[ffffe20001c00000-ffffe20001dfffff] PMD ->ffff810004a00000 on node 0
[ffffe20001e00000-ffffe20001ffffff] PMD ->ffff810004e00000 on node 0
[ffffe20002000000-ffffe200021fffff] PMD ->ffff810005200000 on node 0
[ffffe20002200000-ffffe200023fffff] PMD ->ffff810005600000 on node 0
[ffffe20002400000-ffffe200025fffff] PMD ->ffff810005a00000 on node 0
[ffffe20002600000-ffffe200027fffff] PMD ->ffff810005e00000 on node 0
[ffffe20002800000-ffffe200029fffff] PMD ->ffff810006200000 on node 0
[ffffe20002a00000-ffffe20002bfffff] PMD ->ffff810006600000 on node 0
[ffffe20002c00000-ffffe20002dfffff] PMD ->ffff810006a00000 on node 0
[ffffe20002e00000-ffffe20002ffffff] PMD ->ffff810006e00000 on node 0
[ffffe20003000000-ffffe200031fffff] PMD ->ffff810007200000 on node 0
[ffffe20003200000-ffffe200033fffff] PMD ->ffff810007600000 on node 0
[ffffe20003400000-ffffe200035fffff] PMD ->ffff810007a00000 on node 0
[ffffe20003600000-ffffe200037fffff] PMD ->ffff810007e00000 on node 0
[ffffe20003800000-ffffe200039fffff] PMD ->ffff810008200000 on node 0
[ffffe20003a00000-ffffe20003bfffff] PMD ->ffff810008600000 on node 0
[ffffe20003c00000-ffffe20003dfffff] PMD ->ffff810008a00000 on node 0
[ffffe20003e00000-ffffe20003ffffff] PMD ->ffff810008e00000 on node 0
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1179648
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0 -> 153
0: 256 -> 917424
0: 1048576 -> 1179648
On node 0 totalpages: 1048393
DMA zone: 56 pages used for memmap
DMA zone: 1457 pages reserved
DMA zone: 2480 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 899048 pages, LIFO batch:31
Normal zone: 1792 pages used for memmap
Normal zone: 129280 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at e2000000 (gap: e0000000:1ee00000)
PERCPU: Allocating 38128 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030808
Kernel command line: root=/dev/sda3 pci=nomsi
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
time.c: Detected 1600.055 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x9a20000 - 0xda20000
Memory: 4044964k/4718592k available (2964k kernel code, 147916k
reserved, 1707k data, 276k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 3202.38 BogoMIPS
(lpj=16011916)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Freeing SMP alternatives: 31k freed
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12500425
Detected 12.500 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3200.16 BogoMIPS
(lpj=16000803)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Celeron(R) CPU E1200 @ 1.60GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 0003
groups: 0001 0002
CPU1 attaching sched-domain:
domain 0: span 0003
groups: 0002 0001
net_namespace: 296 bytes
xor: automatically using best checksumming function: generic_sse
generic_sse: 5854.800 MB/sec
xor: using function: generic_sse (5854.800 MB/sec)
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 9B,
should be 90 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI-GART: No AMD northbridge found.
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:07: ioport range 0x290-0x297 has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x480-0x4bf has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
system 00:0a: iomem range 0xffc00000-0xffefffff could not be reserved
system 00:0e: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
system 00:10: iomem range 0x0-0x9ffff could not be reserved
system 00:10: iomem range 0xc0000-0xcffff has been reserved
system 00:10: iomem range 0xe0000-0xfffff could not be reserved
system 00:10: iomem range 0x100000-0xdfffffff could not be reserved
system 00:10: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: e000-efff
MEM window: 0xfbf00000-0xfbffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: d000-dfff
MEM window: 0xfbe00000-0xfbefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
IO window: c000-cfff
MEM window: 0xfbd00000-0xfbdfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: b000-bfff
MEM window: 0xfbc00000-0xfbcfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: a000-afff
MEM window: 0xfbb00000-0xfbbfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: 9000-9fff
MEM window: 0xfba00000-0xfbafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: 8000-8fff
MEM window: 0xfb900000-0xfb9fffff
PREFETCH window: 0x00000000f4000000-0x00000000f7ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA-32 Microcode Update Driver: v1.14a
Total HugeTLB memory allocated, 0
NTFS driver 2.1.29 [Flags: R/W].
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:03.0: Boot video device
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Linux agpgart interface v0.103
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT DFFBE0B0, 01D2 (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: SSDT DFFBE290, 0143 (r1 AMI CPU2PM 1 INTL 20060113)
ACPI: ACPI0007:01 is registered as cooling_device1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
brd: module loaded
loop: module loaded
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:05:00.0 to 64
sky2 0000:05:00.0: v1.21 addr 0xfbdfc000 irq 18 Yukon-EC Ultra (0xb4) rev 3
sky2 eth0: addr 00:1e:8c:c3:48:f2
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:04:00.0 to 64
sky2 0000:04:00.0: v1.21 addr 0xfbcfc000 irq 19 Yukon-EC Ultra (0xb4) rev 3
sky2 eth1: addr 00:1e:8c:c3:47:28
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
sky2 0000:03:00.0: v1.21 addr 0xfbbfc000 irq 16 Yukon-EC Ultra (0xb4) rev 3
sky2 eth2: addr 00:1e:8c:c3:46:af
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 0000:02:00.0: v1.21 addr 0xfbafc000 irq 17 Yukon-EC Ultra (0xb4) rev 3
sky2 eth3: addr 00:1e:8c:c3:44:55
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfb8ffc00 port 0xfb8ffd00 irq 19
ata2: SATA max UDMA/133 abar m1024@0xfb8ffc00 port 0xfb8ffd80 irq 19
ata3: SATA max UDMA/133 abar m1024@0xfb8ffc00 port 0xfb8ffe00 irq 19
ata4: SATA max UDMA/133 abar m1024@0xfb8ffc00 port 0xfb8ffe80 irq 19
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata3.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata4.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 2:0:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 3:0:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg3 type 0
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ahci 0000:07:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:07:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:07:00.0 to 64
scsi4 : ahci
scsi5 : ahci
ata5: SATA max UDMA/133 abar m8192@0xfbffe000 port 0xfbffe100 irq 16
ata6: SATA max UDMA/133 abar m8192@0xfbffe000 port 0xfbffe180 irq 16
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: SAMSUNG HD401LJ, ZZ100-15, max UDMA7
ata5.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata6.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD401LJ ZZ10 PQ: 0 ANSI: 5
sd 4:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 4:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sde: sde1
sd 4:0:0:0: [sde] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg4 type 0
scsi 5:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 5:0:0:0: [sdf] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:0:0:0: [sdf] Write Protect is off
sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 5:0:0:0: [sdf] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:0:0:0: [sdf] Write Protect is off
sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdf: sdf1
sd 5:0:0:0: [sdf] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg5 type 0
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level, low) -> IRQ 17
ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ
ahci 0000:06:00.0: MV_AHCI HACK: port_map 1f -> f
ahci 0000:06:00.0: AHCI 0001.0000 32 slots 5 ports 3 Gbps 0xf impl RAID mode
ahci 0000:06:00.0: flags: 64bit stag pmp slum part
PCI: Setting latency timer of device 0000:06:00.0 to 64
scsi6 : ahci
scsi7 : ahci
scsi8 : ahci
scsi9 : ahci
scsi10 : ahci
ata7: SATA max UDMA/133 abar m1024@0xfbeffc00 port 0xfbeffd00 irq 17
ata8: SATA max UDMA/133 abar m1024@0xfbeffc00 port 0xfbeffd80 irq 17
ata9: SATA max UDMA/133 abar m1024@0xfbeffc00 port 0xfbeffe00 irq 17
ata10: SATA max UDMA/133 abar m1024@0xfbeffc00 port 0xfbeffe80 irq 17
ata11: DUMMY
ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata7.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata7.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata7.00: configured for UDMA/133
ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata8.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata8.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata8.00: configured for UDMA/133
ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata9.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata9.00: configured for UDMA/133
ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata10.00: ATA-6: ST3750330NS, SN04, max UDMA/133
ata10.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata10.00: configured for UDMA/133
scsi 6:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 6:0:0:0: [sdg] 1465149168 512-byte hardware sectors (750156 MB)
sd 6:0:0:0: [sdg] Write Protect is off
sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 6:0:0:0: [sdg] 1465149168 512-byte hardware sectors (750156 MB)
sd 6:0:0:0: [sdg] Write Protect is off
sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdg: sdg1
sd 6:0:0:0: [sdg] Attached SCSI disk
sd 6:0:0:0: Attached scsi generic sg6 type 0
scsi 7:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 7:0:0:0: [sdh] 1465149168 512-byte hardware sectors (750156 MB)
sd 7:0:0:0: [sdh] Write Protect is off
sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 7:0:0:0: [sdh] 1465149168 512-byte hardware sectors (750156 MB)
sd 7:0:0:0: [sdh] Write Protect is off
sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdh: sdh1
sd 7:0:0:0: [sdh] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg7 type 0
scsi 8:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 8:0:0:0: [sdi] 1465149168 512-byte hardware sectors (750156 MB)
sd 8:0:0:0: [sdi] Write Protect is off
sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 8:0:0:0: [sdi] 1465149168 512-byte hardware sectors (750156 MB)
sd 8:0:0:0: [sdi] Write Protect is off
sd 8:0:0:0: [sdi] Mode Sense: 00 3a 00 00
sd 8:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdi: sdi1
sd 8:0:0:0: [sdi] Attached SCSI disk
sd 8:0:0:0: Attached scsi generic sg8 type 0
scsi 9:0:0:0: Direct-Access ATA ST3750330NS SN04 PQ: 0 ANSI: 5
sd 9:0:0:0: [sdj] 1465149168 512-byte hardware sectors (750156 MB)
sd 9:0:0:0: [sdj] Write Protect is off
sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 9:0:0:0: [sdj] 1465149168 512-byte hardware sectors (750156 MB)
sd 9:0:0:0: [sdj] Write Protect is off
sd 9:0:0:0: [sdj] Mode Sense: 00 3a 00 00
sd 9:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdj: sdj1
sd 9:0:0:0: [sdj] Attached SCSI disk
sd 9:0:0:0: Attached scsi generic sg9 type 0
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi11 : ata_piix
scsi12 : ata_piix
ata12: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata13: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata12.00: ATA-7: ST3320620A, 3.AAD, max UDMA/100
ata12.00: 625142448 sectors, multi 16: LBA48
ata12.01: ATA-7: HDS725050KLAT80, K2AOAB0A, max UDMA/133
ata12.01: 976773168 sectors, multi 16: LBA48
ata12.00: configured for UDMA/100
ata12.01: configured for UDMA/100
scsi 11:0:0:0: Direct-Access ATA ST3320620A 3.AA PQ: 0
ANSI: 5
sd 11:0:0:0: [sdk] 625142448 512-byte hardware sectors (320073 MB)
sd 11:0:0:0: [sdk] Write Protect is off
sd 11:0:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 11:0:0:0: [sdk] 625142448 512-byte hardware sectors (320073 MB)
sd 11:0:0:0: [sdk] Write Protect is off
sd 11:0:0:0: [sdk] Mode Sense: 00 3a 00 00
sd 11:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdk: sdk1
sd 11:0:0:0: [sdk] Attached SCSI disk
sd 11:0:0:0: Attached scsi generic sg10 type 0
scsi 11:0:1:0: Direct-Access ATA HDS725050KLAT80 K2AO PQ: 0
ANSI: 5
sd 11:0:1:0: [sdl] 976773168 512-byte hardware sectors (500108 MB)
sd 11:0:1:0: [sdl] Write Protect is off
sd 11:0:1:0: [sdl] Mode Sense: 00 3a 00 00
sd 11:0:1:0: [sdl] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 11:0:1:0: [sdl] 976773168 512-byte hardware sectors (500108 MB)
sd 11:0:1:0: [sdl] Write Protect is off
sd 11:0:1:0: [sdl] Mode Sense: 00 3a 00 00
sd 11:0:1:0: [sdl] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdl: sdl1
sd 11:0:1:0: [sdl] Attached SCSI disk
sd 11:0:1:0: Attached scsi generic sg11 type 0
PCI: Enabling device 0000:07:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:07:00.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:07:00.1 to 64
scsi13 : pata_jmicron
scsi14 : pata_jmicron
ata14: PATA max UDMA/100 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 17
ata15: PATA max UDMA/100 cmd 0xe800 ctl 0xe480 bmdma 0xe408 irq 17
pata_pdc2027x 0000:01:00.0: version 1.0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 21
pata_pdc2027x 0000:01:00.0: PLL input clock 16653 kHz
scsi15 : pata_pdc2027x
scsi16 : pata_pdc2027x
ata16: PATA max UDMA/100 mmio m16384@0xfb9b8000 cmd 0xfb9b97c0 irq 21
ata17: PATA max UDMA/100 mmio m16384@0xfb9b8000 cmd 0xfb9b95c0 irq 21
ata16.00: ATA-7: ST3250824A, 3.AAD, max UDMA/100
ata16.00: 488397168 sectors, multi 16: LBA48
ata16.01: ATA-7: ST3300831A, 3.03, max UDMA/100
ata16.01: 586072368 sectors, multi 16: LBA48
ata16.00: configured for UDMA/100
ata16.01: configured for UDMA/100
ata17.00: ATA-7: SAMSUNG SP2014N, VC100-33, max UDMA/100
ata17.00: 390721968 sectors, multi 16: LBA48
ata17.01: ATA-7: SAMSUNG HD400LD, WQ100-14, max UDMA/100
ata17.01: 781422768 sectors, multi 16: LBA48
ata17.00: configured for UDMA/100
ata17.01: configured for UDMA/100
scsi 15:0:0:0: Direct-Access ATA ST3250824A 3.AA PQ: 0
ANSI: 5
sd 15:0:0:0: [sdm] 488397168 512-byte hardware sectors (250059 MB)
sd 15:0:0:0: [sdm] Write Protect is off
sd 15:0:0:0: [sdm] Mode Sense: 00 3a 00 00
sd 15:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 15:0:0:0: [sdm] 488397168 512-byte hardware sectors (250059 MB)
sd 15:0:0:0: [sdm] Write Protect is off
sd 15:0:0:0: [sdm] Mode Sense: 00 3a 00 00
sd 15:0:0:0: [sdm] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdm: sdm1
sd 15:0:0:0: [sdm] Attached SCSI disk
sd 15:0:0:0: Attached scsi generic sg12 type 0
scsi 15:0:1:0: Direct-Access ATA ST3300831A 3.03 PQ: 0
ANSI: 5
sd 15:0:1:0: [sdn] 586072368 512-byte hardware sectors (300069 MB)
sd 15:0:1:0: [sdn] Write Protect is off
sd 15:0:1:0: [sdn] Mode Sense: 00 3a 00 00
sd 15:0:1:0: [sdn] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 15:0:1:0: [sdn] 586072368 512-byte hardware sectors (300069 MB)
sd 15:0:1:0: [sdn] Write Protect is off
sd 15:0:1:0: [sdn] Mode Sense: 00 3a 00 00
sd 15:0:1:0: [sdn] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdn: sdn1
sd 15:0:1:0: [sdn] Attached SCSI disk
sd 15:0:1:0: Attached scsi generic sg13 type 0
scsi 16:0:0:0: Direct-Access ATA SAMSUNG SP2014N VC10 PQ: 0
ANSI: 5
sd 16:0:0:0: [sdo] 390721968 512-byte hardware sectors (200050 MB)
sd 16:0:0:0: [sdo] Write Protect is off
sd 16:0:0:0: [sdo] Mode Sense: 00 3a 00 00
sd 16:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 16:0:0:0: [sdo] 390721968 512-byte hardware sectors (200050 MB)
sd 16:0:0:0: [sdo] Write Protect is off
sd 16:0:0:0: [sdo] Mode Sense: 00 3a 00 00
sd 16:0:0:0: [sdo] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdo: sdo1
sd 16:0:0:0: [sdo] Attached SCSI disk
sd 16:0:0:0: Attached scsi generic sg14 type 0
scsi 16:0:1:0: Direct-Access ATA SAMSUNG HD400LD WQ10 PQ: 0
ANSI: 5
sd 16:0:1:0: [sdp] 781422768 512-byte hardware sectors (400088 MB)
sd 16:0:1:0: [sdp] Write Protect is off
sd 16:0:1:0: [sdp] Mode Sense: 00 3a 00 00
sd 16:0:1:0: [sdp] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 16:0:1:0: [sdp] 781422768 512-byte hardware sectors (400088 MB)
sd 16:0:1:0: [sdp] Write Protect is off
sd 16:0:1:0: [sdp] Mode Sense: 00 3a 00 00
sd 16:0:1:0: [sdp] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdp: sdp1
sd 16:0:1:0: [sdp] Attached SCSI disk
sd 16:0:1:0: Attached scsi generic sg15 type 0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please
boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
i2c-adapter i2c-0: detect fail: unknown manuf, 0x09
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
w83627ehf: Found W83627DHG chip at 0x290
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
iTCO_vendor_support: vendor-support=0
md: raid1 personality registered for level 1
raid6: int64x1 1501 MB/s
raid6: int64x2 1821 MB/s
raid6: int64x4 1670 MB/s
raid6: int64x8 1120 MB/s
raid6: sse2x1 2851 MB/s
raid6: sse2x2 2978 MB/s
raid6: sse2x4 4750 MB/s
raid6: using algorithm sse2x4 (4750 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
EDAC MC: Ver: 2.1.0 Aug 7 2008
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP htcp registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
md: Autodetecting RAID arrays.
md: Scanned 8 and added 8 devices.
md: autorun ...
md: considering sdj1 ...
md: adding sdj1 ...
md: adding sdi1 ...
md: sdh1 has different UUID to sdj1
md: sdg1 has different UUID to sdj1
md: sdf1 has different UUID to sdj1
md: sdd1 has different UUID to sdj1
md: sdc1 has different UUID to sdj1
md: sdb1 has different UUID to sdj1
md: created md4
md: bind
md: bind
md: running:
raid1: raid set md4 active with 2 out of 2 mirrors
md: considering sdh1 ...
md: adding sdh1 ...
md: adding sdg1 ...
md: sdf1 has different UUID to sdh1
md: sdd1 has different UUID to sdh1
md: sdc1 has different UUID to sdh1
md: sdb1 has different UUID to sdh1
md: created md3
md: bind
md: bind
md: running:
raid1: raid set md3 active with 2 out of 2 mirrors
md: considering sdf1 ...
md: adding sdf1 ...
md: adding sdd1 ...
md: sdc1 has different UUID to sdf1
md: sdb1 has different UUID to sdf1
md: created md2
md: bind
md: bind
md: running:
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdc1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: created md1
md: bind
md: bind
md: running:
raid1: raid set md1 active with 2 out of 2 mirrors
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
EXT3 FS on sda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdm1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdn1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdo1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdp1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdk1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdl1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4008208k swap on /dev/sda2. Priority:-1 extents:1 across:4008208k
sky2 eth3: enabling interface
device eth3 entered promiscuous mode
device tap0 entered promiscuous mode
device tap1 entered promiscuous mode
sky2 eth3: Link is up at 1000 Mbps, full duplex, flow control both
device tap2 entered promiscuous mode
device tap3 entered promiscuous mode
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
br0: port 5(tap3) entering learning state
br0: port 4(tap2) entering learning state
br0: port 3(tap1) entering learning state
br0: port 2(tap0) entering learning state
br0: port 1(eth3) entering learning state
device br0 entered promiscuous mode
sky2 eth0: enabling interface
sky2 eth0: Link is up at 1000 Mbps, full duplex, flow control both
sky2 eth1: enabling interface
sky2 eth2: enabling interface
sky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both
br0: topology change detected, propagating
br0: port 5(tap3) entering forwarding state
br0: topology change detected, propagating
br0: port 4(tap2) entering forwarding state
br0: topology change detected, propagating
br0: port 3(tap1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(tap0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth3) entering forwarding state
vmmon: module license 'unspecified' taints kernel.
[10794]: VMCI: Driver initialized.
[10794]: Module vmmon: registered with major=10 minor=165
[10794]: Module vmmon: initialized
/dev/vmnet: open called by PID 10839 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth1: enabling the bridge
bridge-eth1: up
bridge-eth1: already up
bridge-eth1: attached
/dev/vmnet: open called by PID 10847 (vmnet-bridge)
/dev/vmnet: hub 2 does not exist, allocating memory.
/dev/vmnet: port on hub 2 successfully opened
bridge-eth2: enabling the bridge
bridge-eth2: up
bridge-eth2: already up
bridge-eth2: attached